4

What Are Common Problems Of Keurig Coffee Maker And How To Deal With Them?

Overview

keurig-problemsThe Keurig coffee maker is getting more and more popular in the world of coffee maker for its ease of use, convenience as well as the huge variety of K-cups which offer tasty coffee, hot chocolate or tea. However, everything has two sides, in spite of so many praises like this, there are some keurig coffee maker problems remaining. And my honest article today will address some of the most common keurig problems and ways to deal with them as well. You will finally have your best keurig work fine.

What are common keurig problems and how to deal with them?

Grounds in your cup

This is common issue that many of us have experienced. It often happens when the needle which stabs the K-cup gets clogged with the grounds and the trapped grounds move to your cup on the next brewing, resulting in a horrible grainy texture in your coffee. But don’t be worried too much, this issue can be easily repaired, just by washing the needle with a fine pointy item like a toothpick. And it often mentioned as keurig 2.0 problems. After this needle cleaning, you can enjoy tasty Keurig K-cup coffee, with no grainy grounds remained in your cup!

Plastic tasting coffee

This keurig problems often happens with new Keurig Single Serve coffee machines. When it happens, you will find the coffee brew has a different plastic taste which is unpleasant. It is caused when the residue of the new brewing parts is transmitted to the water throughout the brewing procedure. It can be resolved just by rinsing the brewing line, using white vinegar. So how to conduct the rinsing process? Yeah, here is the specific step:

  • Add a cup of white vinegar in the water container.
  • Have the brew cycle run repeatedly until the container is completely empty, this process will help to clean the brewing line as well as remove plastic taste.
  • It’s now time to rinse the line with water, to stop possible vinegar taste: Pour filtered water in the container and operate the brew cycle until the container is empty.

Ok, now continue your process and making your tasty coffee, there will be no plastic taste remained!

Water line is clogged

Water lines in Keurig brewers are often small, so it can be clogged with grounds and other debris easily. This is a very common keurig problem that you can identify when you find a lesser quantity of coffee in your cup than the amount you have selected before. In case the clog is too bad, you even get no coffee after a brewing cycle! To repair this, blush the water line by operating the brewing cycle with water only, no K-cup. In addition, clean the needle to take out grounds which might be stuck inside. Finally, you will find your water line open and get ready to give you a full cup of great-tasting coffee.

In case the water line has been cleaned up yet, then try descaling the device. And this process will promise to deliver tasty coffee at the push of a button, even it is keurig 2.0 problems,  Keurig k45 or any other ones.

Machine shuts off between brew cycles

Ok, if your Keurig single serve brewer suddenly shuts off during brew cycles, even you have not switched it off, don’t feel worried. Many users have experienced it, too.

This issue is cause due to the fact that the vibrations have dislodged the magnet in the water reservoir. So to deal with it, simply take out the reservoir, then assemble it again, make sure that the magnet is set in correct position. And now, let’s resume your brewing.

The Keurig Brewer is leaking water

If you find some leakages in your Keurig brewer, you are likely to have a keurig problems that the upper rubber gasket is missing, faulty, or inappropriately installed. This part is placed around the upper puncture needle, so to deal with the issue, check whether it is in the place. If not, purchase another one, or contact Keurig if your guarantee is still valid. In case it is still available and the leakage is happening, the issue is due to incorrect adjustment since it is not forming a seal with the K-cup and incoming water, which causes the water and grounds to leak out and make a mess. To repair this, just move the gasket down about ¼ inch to close up the gap between the needle and the K-cup.

Mineral Build-up

Some users assume this issue is a design problem, but it is more of a usual maintenance issue. Every coffee machine needs to be descaled at some point, and the Keurig model is not an exception.

After certain time of using, mineral from the water passing through the brew line will form and make effects on the competence of your brewer. This may also influence your coffee taste since the mineral build-up is likely to cause an unpleasant flavor in your cup. And to descale your machine, buy a “Brew Rite Cleaner” which is particularly designed to remove mineral deposits. Ok, to have this device worked, let’s add water in the Brew Rite Cleaner and make a brew cycle to blush the water line. You can also use white vinegar instead of water, but then remember to use water to eliminate the vinegar. And no matter what way you apply, conduct it every 6 month to have your machine operated optimally.

Final Words

Ok, so have you ever experienced any of the Keurig problems above? Did you deal with it in correct way? And does your machine work fine after your resolving? The information in this article will claim to help you deal with the issue in the best way. Are you ready to try? Give us your own reviews after the process.

keurigmodel
 

Click Here to Leave a Comment Below 4 comments
Jerry - January 13, 2016

Coffee not hot enough is there a way to make it hotter

Reply
maria - March 13, 2016

Touch screen goes blank. I unplug and reset. Brews once..and it happens again.

Reply
Kathie eberle - March 26, 2016

My K cups won’t go down all the way so am unable to close the machine to brew. What can I do?

Reply

Leave a Reply: